![]() ![]() Make sure you have a mouse and monitor connected. ![]() Once you have the information pertaining to your area written down, we’ll turn our attention to our recorder. The area within AZ that is part of the Navajo Nation, however- does observe DST. The majority of the state of Arizona does not observe DST. The state of Hawaii does not observe DST at all and should leave all DST settings disabled. This is when the clocks are turned forward.ĭST always ends the first Sunday in November, also at 2 am- this is when clocks are rolled back one hour. Refer to the map below for that info:Īcross the USA, DST always begins at 2 Am on the 2nd Sunday in March. Once you know your timezone and UTC write it down. This is expressed as UTC -5:00 which means we are 5 hours behind Coordinated Universal Time. How to Set Date and Time in Dvr – Important Info:ĭepending on what state you live in you’ll fall into a specific timezone, for us here in Florida we are the Eastern timezone. We’re going to explain to you how to do that right now- but first, there’s some information you’ll need. That’s why it’s so important to make sure your recorder time settings are correct. If the footage is needed to be presented in court as evidence- a time mismatch could very likely cause the footage to be inadmissible in court and essentially thrown out. However, even if you are able to find mismatched footage and back it up to a drive- it may not matter. The first problem this causes is that searching the recorder’s system for that footage later can be made difficult or impossible, as the time an event occurred in the real world vs the timestamp will not be the same. Improper time settings will eventually result in an incorrect timestamp on the footage by an hour or more. All recorded footage has a timestamp- and the timestamp is based on your recorders and/or cameras current time settings. There are two important reasons why- and they’re both related to your footage’s timestamp. Ok so now we’ve shown you all the related recorder time settings, but before we show you how to set them up we really want to stress to you how important it is to do so. How to Set Date and Time in Dvr – Why your time needs to be accurate: This means that each year, there is one 23 hour day, and one 25 hour day. In the wintertime, everyone does the reverse and sets their clocks back one hour on the same day and time. The reasoning for this is so that the clock would be more in line with seasonal darkness occurring “later” each day. The idea was that in the spring everyone sets their clocks forward precisely one hour on the same day and time. In 1895, George Hudson came up with daylight saving time. With all that in mind, there’s still one more factor in determining you have the most accurate time set on your recorder and that is Daylight savings time. Each time zone represents how a given area’s time is a certain number of hours ahead of or behind the baseline UTC. In the United States, we have 5 time zones counting Hawaii. Speaking of time-zones- the world and our country is divided into many different ones. How to Set Date and Time in Dvr – Timezones: This is done by connecting to various NTP servers via the web, or via a GPS based NTP device Your recorder can use NTP to check its timezone settings against UTC to remain accurate. Its purpose is to sync the time on any computer devices to Coordinated Universal time or -UTC- the baseline time the entire world uses. Its one of the oldest Internet protocols and has been around since around 1985. We urge you to watch the included video, like, and subscribe to our channel for more content! How to Set Date and Time in DVR or NVRįirstly – NTP is the Network Time Protocol. This includes NTP, timezone, and Daylight Savings Time. All other trademarks or registered trademarks are the property of their respective owners.Hey everyone, Joe here with a very important tutorial, today- we’re going to teach you all about how to Set Date and Time in DVR or NVR. Seagate, Seagate Technology, the Spiral logo are trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. Seagate reserves the right to change, without notice, product offerings or specifications. Actual data rates may vary depending on operating environment and other factors. Actual quantities will vary based on various factors, including file size, file format, features, and application software. Quantitative usage examples for various applications are for illustrative purposes. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Your computer’s operating system may use a different standard of measurement and report a lower capacity. * When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |